Your Kawasaki ZX6R / ZX636 already has a standalone ECU and now you can get a cable and software to re-program it!
There is no longer any need to send us your ECU to remap, you can buy our DIY kit to fit to your own bike and remap and modify your own ECU!
You can also directly import Power Commander III .djm or Power Commander V 5 .pvm fuel maps!
You can de-restrict and Unleash Your bike’s ECU in 7 Easy Steps!
- Select your base map (3 base maps are currently included)
- Select your Ycc-T throttle map settings
- Select your desired fuel map bias
- Select your desired Engine Braking
- Import a fuel map file
- Choose your options (bypass EURO immobilizer, lower fan temps, speedohealer, rev limiter)
- Flash the ECU!
This Interface will remap & flash any ECU from the following bike models!
- ZX636 2019 2020
- ZX6R 2019 2020
- 2019 ZX636 – 21175-1387(US-ABS) StockECU
- 2019 ZX636 – 21175-1395(US) StockECU
- ECU Mapping
- STP Throttle
- Traction Control
- ECU Settings
- Fan Temps
- Decel Fuel Cut
- Warmup Fast-Idle
- Force QSS on
- Exhaust Valve
- ECT / USB Error
- Stock O2
- Evap Purge Valve
- Air Switching Valve
- ECU Modules
- PC Fuel Import
- ECU Mapping
- 2019 ZX636 – 21175-1386(US) StockECU
- 2019 ZX636 – 21175-1396(US) StockECU
The Flash-Tune Remap Interface allows you to easily adjust the following!
- Enable Quickshifter
- Enable Launch Control
- Enable Pit Lane Limiter
- Reduce Engine Braking
- Remove Ycc-t Throttle Restrictions
- Adjust Fuel Map Bias
- Set High Load Fuel Maps (with PC3 and PC5 / PCV map importing)
- Set Low Load (cruising) Fuel Maps for economy and Smoothness
- Set Closed loop on O2 sensor (for more accurate tuning on a dyno)
- Fuel Injector Proportioning
- Modify Ignition Timing
- Remove Immobilizer Function (mandatory on EU models)
- Adjust Cooling Fan Temps
- Adjust Rev-Limiter
- Remove Top Speed Limiter
- YCC-I RPM Control
- Adjust Idle Speed Adjustment
- ECU Based Quick-shifting (requires a Quickshifter kit)
- Turn off AIS Pump
- SpeedoHealer features – adjust the speedo to suit your fitted font and rear sprockets
- Change Speedo into Gear indicator (10=1st, 20=2nd etc)
- Permanently Remove ECU error codes
- plus new features added with regular updates.
This Data-Link ECU Flashing Kit Includes:
- FTdataLink ECU Interface USB Cable
- Bike-side programming harness to permanently install on your bike
- FT ECU License to allow unlimited flashes for a single ecu
– Power Commander or other piggy back fuel controllers
– Power Commander Secondary Fuel Module
– Power Commander Ignition Module
– Bazzaz ZFTi
– Two Brothers JuiceBox
– Leo Vince Fast II fuel and ignition box
ECU flashing is not only more cost effective than its alternatives but it is superior because but it also allows for more precise tuning fuel maps which automatically compensate for changing atmospheric conditions it allows for modification of parameters that are not otherwise tunable such a throttle valve actuation and engine brakingEveryone deserves the same tuning technology that until now was reserved for factory teams and riders with their YEC race kits. With Flash-Tune you can remove the restrictions that the factory must put in place to meet strict street vehicle emissions regulations for homologation, without the need for the factory race loom and factory YEC ECU.
By using Flash-Tune to remap your ECU you are able to remap and tune your bike without interfering with critical correction factors resulting in smoother power gains than ever before possible.
Flash-Tune Remap Products are under constant development. This product is for RACE USE ONLY and may invalidate your warranty.
The included software will automatically update when connected to the internet as new features are added!