6P_BNKT_25 – FTecu FlashTune kit for Kawasaki ZX636 ZX6R 2024+

Description

Data-Link Bench ECU Flashing Kit Includes:

-FTdataLink ECU Interface USB Cable
-Bench Flashing Harness to flash your ECU outside of the bike
-Power Supply for Bench flashing (Compatible with International power outlets)
-FT ECU License to allow unlimited flashes for a single ecu

This Interface will remap & flash any ECU from the following bike models!

• ZX6R ZAX636 NINJA 2024 2025

Example settings

•  2024 ZX636 – 21175-1916(US) StockECU.ftm
•  2024 ZX636 – 21175-1926(CAL) StockECU.ftm
•  2024 ZX636 – 21175-1925(US) StockECU.ftm
•  2024 ZX636 – 21175-1912(EU) StockECU.ftm
  •  ECU Mapping
    •  Fuel
      •  Fuel MAP vs RPM
      •  Fuel TPS vs RPM
      •  Fuel Trim
      •  INJ timing
      •  Water Temp Correction
    •  Ignition
      •  IGN Advance
    •  STP Throttle
      •  STP Static Target
      •  STP Accel Control
      •  STP Decel Control
    •  Traction Control
      •  TC Activation Threshold
      •  TC Sensitivity TPS
      •  TC Sensitivity Slip
    •  Qickshifter Control
      •  RPM Adjustment
      •  Gear Adjustment
  •  ECU Settings
    •  Fan Temps
    •  Rev Limiters
    •  Decel Fuel Cut
    •  Warmup Fast-Idle
    •  ECT / USB Error
    •  Exhaust Valve
    •  Stock O2
    •  Air Switching Valve
    •  EVAP Purge Valve
    •  Radiator Fan
  •  ECU Modules
    •  PC Fuel Import
•  2024 ZX636 – 21175-1917(CAL) StockECU.ftm

The Flash-Tune Remap Interface allows you to easily adjust the following!

•   Enable Quickshifter
•   Enable Launch Control
•   Enable Pit Lane Limiter
•   Reduce Engine Braking
•   Remove Ycc-t Throttle Restrictions
•   Adjust Fuel Map Bias
•   Set High Load Fuel Maps (with PC3 and PC5 / PCV map importing)
•   Set Low Load (cruising) Fuel Maps for economy and Smoothness
•   Set Closed loop on O2 sensor (for more accurate tuning on a dyno)
•   Fuel Injector Proportioning
•   Modify Ignition Timing
•   Remove Immobilizer Function (mandatory on EU models)
•   Adjust Cooling Fan Temps
•   Adjust Rev-Limiter
•   Remove Top Speed Limiter
•   YCC-I RPM Control
•   Adjust Idle Speed Adjustment
•   ECU Based Quick-shifting (requires a Quickshifter kit)
•   Turn off AIS Pump
•   SpeedoHealer features – adjust the speedo to suit your fitted font and rear sprockets
•   Change Speedo into Gear indicator (10=1st, 20=2nd etc)
•   Permanently Remove ECU error codes
•   plus new features added with regular updates.

This Data-Link ECU Flashing Kit Includes:

• FTdataLink ECU Interface USB Cable
• Bike-side programming harness to permanently install on your bike
• FT ECU License to allow unlimited flashes for a single ecu

– Power Commander or other piggy back fuel controllers
– Power Commander Secondary Fuel Module
– Power Commander Ignition Module
– Bazzaz ZFTi
– Two Brothers JuiceBox
– Leo Vince Fast II fuel and ignition box

ECU flashing is not only more cost effective than its alternatives but it is superior because but it also allows for more precise tuning fuel maps which automatically compensate for changing atmospheric conditions it allows for modification of parameters that are not otherwise tunable such a throttle valve actuation and engine brakingEveryone deserves the same tuning technology that until now was reserved for factory teams and riders with their YEC race kits. With Flash-Tune you can remove the restrictions that the factory must put in place to meet strict street vehicle emissions regulations for homologation, without the need for the factory race loom and factory YEC ECU.

By using Flash-Tune to remap your ECU you are able to remap and tune your bike without interfering with critical correction factors resulting in smoother power gains than ever before possible.

Flash-Tune Remap Products are under constant development. This product is for RACE USE ONLY and may invalidate your warranty.

The included software will automatically update when connected to the internet as new features are added!